- #Show mac address fortinet license key
- #Show mac address fortinet Patch
- #Show mac address fortinet full
- #Show mac address fortinet software
- #Show mac address fortinet password
All communications with the cluster must use this MAC address. When operating in HA mode, all of the interfaces of the primary unit acquire the same HA virtual MAC address. If any single component or any single connection fails, traffic switches to the redundant component or connection.
#Show mac address fortinet full
Full mesh HA includes redundant connections between all network components. FortiGate models that support redundant interfaces can be used to create a cluster configuration called full mesh HA. The FortiGate clustering protocol (FGCP) that specifies how the FortiGate units in a cluster communicate to keep the cluster operating.įull mesh HA is a method of removing single points of failure on a network that includes an HA cluster.
#Show mac address fortinet software
Device failover means that if a device fails, a replacement device automatically takes the place of the failed device and continues operating in the same manner as the failed device.Ī FortiGate unit taking over processing network traffic in place of another unit in the cluster that suffered a device failure or a link failure.Ī hardware or software problem that causes a FortiGate unit or a monitored interface to stop processing network traffic. Terminology UsedĪ group of FortiGate units that act as a single virtual FortiGate unit to maintain connectivity even if one of the FortiGate units in the cluster fails.Ī FortiGate unit operating in a FortiGate HA cluster.ĭevice failover is a basic requirement of any highly available system. In that way if the switch connecting one of the heartbeat interfaces fails or is unplugged, heartbeat traffic can continue on the other heartbeat interfaces and switch.
For improved redundancy use a different switch for each heartbeat interface. The corresponding heartbeat interface of each FortiGate unit in the cluster must be connected to the same switch. If switches have to be used they should not be used for other network traffic that could flood the switches and cause heartbeat delays.įor clusters of three or four FortiGate units, use switches to connect heartbeat interfaces.
#Show mac address fortinet Patch
Heartbeat Interface – For clusters of two FortiGate units, as much as possible, heartbeat interfaces should be directly connected using patch cables (without involving other network equipment such as switches). I recommend getting the cluster configured first and THEN add the monitored interface to the config. Monitor Interface – These are the interfaces that they Fortigate will montitor for failure. This can be a huge problem for traffic that is connection oriented and has little resilience (e.g. After a device or link failover all sessions are briefly interrupted and must be re-established at the application level after the cluster renegotiates. Session Pickup – If Enable Session Pick-up is not selected, the Fortigates do not maintain an HA session table and most TCP sessions do not resume after a failover. Two clusters on the same network cannot have the same password. When the cluster is operating you can change the password, if required.
#Show mac address fortinet password
The password must be the same for all FortiGate units before they can form a cluster. You should always change the password when configuring a cluster. Password – Use the password to identify the cluster. The group name appears on the FortiGate dashboard of a functioning cluster as the Cluster Name. The group name change is synchronized to all cluster units. After a cluster is operating, you can change the group name. The group name must be the same for all cluster units before the cluster units can form a cluster. The maximum length of the group name is 32 characters.
Group Name – Use the group name to identify the cluster. The higher the priority the higher probability of becoming ‘master’. Once you lose a box, you will have 40% unaccounted for.ĭevice Priority – This setting will tell the cluster which device will be the Master and which will be the slave. NOTE: I do not suggest Active/Active since you do not want to be in a scenario where you have 70% load on one box and 70% load on the other. Your options are Standalone (the default), Active/Active and Active/Passive. To configure HA on the Fortigate, go to SYSTEM -> HA Then select the mode.
#Show mac address fortinet license key
This includes FortiCloud activation and FortiClient licensing, and entering a license key if you purchased more than 10 Virtual Domains (VDOMS) Register and apply licenses to both FortiGates before adding them to the cluster. Before we begin configuring HA, rename the boxes with descriptive names referring to Primary and Secondary (whatever works for you). When you configure HA on the Fortigate, it is required to have the same hardware, and FortiOS version. Today, I am writting one on Fortigate HA. Last month I wrote a blog post about HA on the ASA.
0 kommentar(er)
